Today's Message Index:
----------------------
 
     1. 04:46 AM - Re: Congrats Tommy! (Geoff Heap)
     2. 04:48 AM - Re: In the air (Geoff Heap)
     3. 05:07 AM - Re: EGT probe locations for 912S with Zenith exhaust? (Geoff Heap)
     4. 10:19 AM - Re: dent removal question (Jimmy Young)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
04:46:15 AM PST US
Subject: 
Re: Congrats Tommy!
From: 
"Geoff Heap" <stol10@comcast.net>
      
      
      You must feel terrific Tommy. Congratulations. Who made the first flight?
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=291398#291398
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
04:48:33 AM PST US
Subject: 
Re: In the air
From: 
"Geoff Heap" <stol10@comcast.net>
      
      
      You must feel terrific Tommy. Congratulations. Who made the first flight?
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=291399#291399
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
05:07:49 AM PST US
Subject: 
Re: EGT probe locations for 912S with Zenith exhaust?
From: 
"Geoff Heap" <stol10@comcast.net>
      
      
      John. I just drilled mine (912UL) as per the Dynon installation manual. They suggest
      2" to 8" from the cylinder. This works out nice as 6" comes at a very nice
      straight stretch on the two rear headers. Sorry my input came a little late.
      Did you resolve it and drill them yet. I also bought some header wrap for these
      areas only, to protect the cooling hoses that pass so close by........Geoff
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=291402#291402
      
      

Message 4


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
10:19:51 AM PST US
Subject: 
Re: dent removal question
From: 
"Jimmy Young" <jdy100@comcast.net>
      
      
      I used a little heat & spooned the dent out a bit more, then 3 or 4 more heat/ice
      cycles, and got most of the "bubble" out. Since it's on the leading edge the
      bubble will flatten out (I free-formed the sheet to it's eventual shape to check
      this) and the best news is the location is under the slat so that helps as
      well. Thanks again for the tips.
      
      Jimmy Y
      750 builder
      Houston TX
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=291448#291448
      
      








Other Matronics Email List Services




Post A New Message
  
zenith701801-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Zenith701801-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/zenith701801-list
Browse Zenith701801-List Digests
  
http://www.matronics.com/digest/zenith701801-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --