Today's Message Index:
----------------------
1. 04:46 AM - Chat Tonight (George Race)
2. 06:15 AM - Re: Matco Gear Bolt Pattern? (Randall J Hebert)
3. 07:40 AM - Re: Matco Gear Bolt Pattern? (Mike Weesner)
4. 08:46 AM - Re: Matco Gear Bolt Pattern? (John Marzulli)
5. 09:26 AM - Re: Matco Gear Bolt Pattern? (Mark Sherman)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Live Chat Room every Monday evening around 8:00 EDT
http://www.mykitairplane.com <blocked::http://www.mykitairplane.com/>
Click on the Chat Room link at the top of the page.
George
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Matco Gear Bolt Pattern? |
Try
www.kobushweldingandmachining.com
Go to the aircraft tools
There is a drill guide that worked well for me.
Randall J Hebert
Randall J Hebert & Associates, Inc
Consulting Engineers
Ph 337-261-1976 Fx 337-261-1977
From: owner-zenith701801-list-server@matronics.com
[mailto:owner-zenith701801-list-server@matronics.com] On Behalf Of John
Marzulli
Sent: Sunday, January 09, 2011 10:34 PM
Subject: Re: Zenith701801-List: Matco Gear Bolt Pattern?
I know you are supposed to transfer punch them, but I remember seeing a
pattern in the Matco manual.
Can anyone confirm that the holes are 1.75" apart?
John Marzulli
http://MarzulliPhoto.net/
http://701Builder.blogspot.com/
On Sun, Jan 9, 2011 at 6:14 PM, MacDonald Doug <dougsnash@yahoo.com> wrote:
John, you are suposed to remove the axel from the wheel then use a transfer
punch to center punch the gear spring through the bolt holes in the axle.
There is no template for the Matco axels other than this.
Doug MacDonald
CH-701 C-GBQX
NW Ontario, Canada
Phase One
Do Not Archive
--- On Sun, 1/9/11, John Marzulli <john.marzulli@gmail.com> wrote:
From: John Marzulli <john.marzulli@gmail.com>
Subject: Zenith701801-List: Matco Gear Bolt Pattern?
Received: Sunday, January 9, 2011, 5:04 PM
I have decided to use the Grove gear instead of the Zenith supplied leaf.
Can anyone supply the bolt pattern for the stock Matco gear that Zenith
supplies? I can't find the original Matco instructions.
Thanks,
John Marzulli
http://MarzulliPhoto.net/
http://701Builder.blogspot.com/
ist" rel=nofollow
target=_blank>http://www.matronics.com/Navigator?Zenith701801-List
et=_blank>http://forums.matronics.com
llow target=_blank>http://www.matronics.com/contribution
ist" target="_blank">http://www.matronics.com/Navigator?Zenith701801-List
tp://forums.matronics.com
_blank">http://www.matronics.com/contribution
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Matco Gear Bolt Pattern? |
On Sun, 9 Jan 2011 18:14:49 -0800 (PST)
MacDonald Doug <dougsnash@yahoo.com> wrote:
> John, you are suposed to remove the axel from the wheel
>then use a transfer punch to center punch the gear spring
>through the bolt holes in the axle. There is no template
>for the Matco axels other than this.
>
> Doug MacDonald
> CH-701 C-GBQX
> NW Ontario, Canada
> Phase One
>
> Do Not Archive
>
> --- On Sun, 1/9/11, John Marzulli
><john.marzulli@gmail.com> wrote:
>
>
>From: John Marzulli <john.marzulli@gmail.com>
> Subject: Zenith701801-List: Matco Gear Bolt Pattern?
> To: zenith701801-list@matronics.com
> Received: Sunday, January 9, 2011, 5:04 PM
>
>
> I have decided to use the Grove gear instead of the
>Zenith supplied leaf.
>
> Can anyone supply the bolt pattern for the stock Matco
>gear that Zenith supplies? I can't find the original
>Matco instructions.
>
> the template block that can be bought online is of great help
> Thanks,
>
> John Marzulli
>
> http://MarzulliPhoto.net/
> http://701Builder.blogspot.com/
>
>
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Matco Gear Bolt Pattern? |
My point is that I want to get the axle pre-drilled by Grove, so I need to
bolt pattern.
Thanks,
John Marzulli
http://MarzulliPhoto.net/
http://701Builder.blogspot.com/
On Mon, Jan 10, 2011 at 7:36 AM, Mike Weesner <mikeweesner@multipro.com>wrote:
> mikeweesner@multipro.com>
>
> On Sun, 9 Jan 2011 18:14:49 -0800 (PST)
>
> MacDonald Doug <dougsnash@yahoo.com> wrote:
>
>> John, you are suposed to remove the axel from the wheel then use a
>> transfer punch to center punch the gear spring through the bolt holes in the
>> axle. There is no template for the Matco axels other than this.
>>
>> Doug MacDonald
>> CH-701 C-GBQX
>> NW Ontario, Canada
>> Phase One
>>
>> Do Not Archive
>>
>> --- On Sun, 1/9/11, John Marzulli <john.marzulli@gmail.com> wrote:
>>
>>
>> From: John Marzulli <john.marzulli@gmail.com>
>> Subject: Zenith701801-List: Matco Gear Bolt Pattern?
>> To: zenith701801-list@matronics.com
>> Received: Sunday, January 9, 2011, 5:04 PM
>>
>>
>> I have decided to use the Grove gear instead of the Zenith supplied leaf.
>>
>> Can anyone supply the bolt pattern for the stock Matco gear that Zenith
>> supplies? I can't find the original Matco instructions.
>>
>> the template block that can be bought online is of great help
>>
>> Thanks,
>>
>> John Marzulli
>>
>> http://MarzulliPhoto.net/
>> http://701Builder.blogspot.com/
>>
>>
>>
>>
>>
>>
>
>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Matco Gear Bolt Pattern? |
If I was spending a thousand bucks on a landing gear from Grove
They had better know what the bolt pattern is or find out.
Mark S.
701/912uls
Sent from Mark's iPhone
On Jan 10, 2011, at 8:29 AM, John Marzulli <john.marzulli@gmail.com> wrote:
> My point is that I want to get the axle pre-drilled by Grove, so I need t
o bolt pattern.
>
> Thanks,
>
> John Marzulli
>
> http://MarzulliPhoto.net/
> http://701Builder.blogspot.com/
>
>
> On Mon, Jan 10, 2011 at 7:36 AM, Mike Weesner <mikeweesner@multipro.com> w
rote:
pro.com>
>
> On Sun, 9 Jan 2011 18:14:49 -0800 (PST)
>
> MacDonald Doug <dougsnash@yahoo.com> wrote:
> John, you are suposed to remove the axel from the wheel then use a transfe
r punch to center punch the gear spring through the bolt holes in the axle.
There is no template for the Matco axels other than this.
>
> Doug MacDonald
> CH-701 C-GBQX
> NW Ontario, Canada
> Phase One
>
> Do Not Archive
>
> --- On Sun, 1/9/11, John Marzulli <john.marzulli@gmail.com> wrote:
>
>
> From: John Marzulli <john.marzulli@gmail.com>
> Subject: Zenith701801-List: Matco Gear Bolt Pattern?
> To: zenith701801-list@matronics.com
> Received: Sunday, January 9, 2011, 5:04 PM
>
>
> I have decided to use the Grove gear instead of the Zenith supplied leaf.
>
> Can anyone supply the bolt pattern for the stock Matco gear that Zenith su
pplies? I can't find the original Matco instructions.
>
> the template block that can be bought online is of great help
>
> Thanks,
>
> John Marzulli
>
> http://MarzulliPhoto.net/
> http://701Builder.blogspot.com/
>
>
>
>
>
>
>
> ==========
> -List" target="_blank">http://www.matronics.com/Navigator?Zenith701801-L
ist
> ==========
> http://forums.matronics.com
> ==========
> le, List Admin.
> ="_blank">http://www.matronics.com/contribution
> ==========
>
>
>
>
>
>
==========================
=========
==========================
=========
==========================
=========
==========================
=========
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|