---------------------------------------------------------- Zenith701801-List Digest Archive --- Total Messages Posted Wed 03/02/11: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:13 AM - Re: Control Issues in Phase 1 testing (fritz) 2. 05:24 AM - Control Issues in Phase 1 testing (Joe Spencer) 3. 11:04 AM - Re: Control Issues in Phase 1 testing (cdnch701) 4. 01:54 PM - Re: Control Issues in Phase 1 testing (Carl) 5. 02:49 PM - Re: Control Issues in Phase 1 testing (fritz) 6. 08:33 PM - Re: Control Issues in Phase 1 testing (JohnDRead@aol.com) ________________________________ Message 1 _____________________________________ Time: 05:13:39 AM PST US From: "fritz" Subject: Re: Zenith701801-List: Control Issues in Phase 1 testing Dan-- Sounds like you still have the bend at the trailing edge of the elevator. Many moons ago, Chris said to take the bend out. Fritz ----- Original Message ----- From: "txpilot" Sent: Wednesday, March 02, 2011 12:31 AM Subject: Zenith701801-List: Control Issues in Phase 1 testing > > > I now have 16 hours on my 701 and I've found a few issues that are > curious, to say the least. > > First, it seems the aircraft cannot be trimmed for level flight with the > flaps down. Although the elevator trim is neutral or slightly down in > cruise with the flaps up, no amount of up elevator trim will prevent the > airplane from nose-diving (HARD) with the flaps down. > > Second, I'm following the AC 90-89A guide for test-flying my airplane. > I'm conducting the "Lateral-directional Stability Control Tests" described > on page 51 of this document. I've found the rudder will not spring back > to neutral in flight but will instead maintain its last set position, even > at near full deflection! I think it's because there is no vertical > stabilizer and there's a lot of rudder surface area ahead of the rudder > hinge. I'm concerned a full deflection, especially near maneuvering > speed, may cause a control lock in full rudder deflection. > > Third, I conducted the "Spiral Stability" check described in the same > Advisory Circular. To my surprise, the aircraft maintains neutral > stability (i.e. - it will not return from a banked condition to level > flight). This is not typical of high wing aircraft. Although this is not > a critical safety issue, it does make the airplane a little more difficult > to fly. > > Has anyone else noticed these issues in their aircraft? > > Thanks, > > Dan Ginty > N787DG > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=332451#332451 > > > ________________________________ Message 2 _____________________________________ Time: 05:24:11 AM PST US From: "Joe Spencer" Subject: Zenith701801-List: Control Issues in Phase 1 testing Yes , we've noticed. Those are pretty much "normal" 701 flight characteristics; to varying degrees. Welcome to the 701... ________________________________ Message 3 _____________________________________ Time: 11:04:49 AM PST US From: cdnch701 Subject: Re: Zenith701801-List: Control Issues in Phase 1 testing Dan Sounds like you have the problem with running out of elevator other builders have! Attached is CH's cure for the problem... they should re-publish in Zenair news to make everywhere of the problem. They never the change to the drawings... after they went to the heavier 912 engine! Ron :--) :--) :--) I now have 16 hours on my 701 and I've found a few issues that :--) are curious, to say the least. :--) :--) First, it seems the aircraft cannot be trimmed for level flight :--) with the flaps down. Although the elevator trim is neutral or :--) slightly down in cruise with the flaps up, no amount of up :--) elevator trim will prevent the airplane from nose-diving (HARD) :--) with the flaps down. :--) :--) Second, I'm following the AC 90-89A guide for test-flying my :--) airplane. I'm conducting the "Lateral-directional Stability :--) Control Tests" described on page 51 of this document. I've :--) found the rudder will not spring back to neutral in flight but :--) will instead maintain its last set position, even at near full :--) deflection! I think it's because there is no vertical :--) stabilizer and there's a lot of rudder surface area ahead of the :--) rudder hinge. I'm concerned a full deflection, especially near :--) maneuvering speed, may cause a control lock in full rudder :--) deflection. :--) :--) Third, I conducted the "Spiral Stability" check described in the :--) same Advisory Circular. To my surprise, the aircraft maintains :--) neutral stability (i.e. - it will not return from a banked :--) condition to level flight). This is not typical of high wing :--) aircraft. Although this is not a critical safety issue, it does :--) make the airplane a little more difficult to fly. :--) :--) Has anyone else noticed these issues in their aircraft? :--) :--) Thanks, :--) :--) Dan Ginty :--) N787DG :--) :--) :--) Read this topic online here: :--) :--) http://forums.matronics.com/viewtopic.php?p=332451#332451 :--) :--) :--) :--) = - MATRONICS WEB FORUMS - :--) your generous support! :--) --> http://www.matronics.com/contribution ________________________________ Message 4 _____________________________________ Time: 01:54:23 PM PST US From: Carl Subject: Re: Zenith701801-List: Control Issues in Phase 1 testing Dan I believe the V blocks on the nose gear bearing are designed to return the rudder to the neutral position in flight to act as a fin and provide directional stability. Unfortunately they are not always effective if the rudder control system has a lot of friction; and the system does have a lot of friction. You may want to try and reduce friction and check if your blocks are optimized.. In my case, since the blocks did not seam to help much and had to keep my feet on the pedals all the time, I installed a nose wheel steering disconnect to reduce the friction. in flight. This makes the rudder control lighter and spares the legs on long flights. The rudder pretty much acts as it did before; when deflected up to two ball width, it stays deflected. and needs to be returned ,even with the reduced friction in my system. This shows that the a|c minus rudder has close to 0 stability; that being the case there is no aerodynamic force to return the rudder to neutral so it stays aligned with the airflow. In cruise, I found that once the a|c is in trim and the rudder is in neutral just using the pedals as foot rest gives a pretty comfortable ride even in light turbulence. In that situation the rudder becomes a big fin and for a small, a|c gives good directional stability. I experimented by adding a ventral fin (about two 2 sqf). It did little for stability in the air but made the aircraft much more difficult to turn downwind on the water (I`m on floats).So it came off.and is now a conversation item on the wall in my hangar. As to your concern about rudder lock, my testing with floats (they make the a|c less directionally stable) I find that the rudder becomes harder to deflect from neutral : 1- the further it is deflected: and 2 -the higher the IAS. I must emphasise that I have not conducted this test at any where close to manoeuvring speed but I doubt a rudder lock could happen. In summary. the testing I have done leads me to believe the rudder is effective and when used properly control the a|c in all normal manoeuvres. Since the rudder is also a large part of the fin area, I expect the loss of same would render the a|c uncontrollable. So I check rudder very closely before flight. Carl ays ----- Original Message ----- From: "txpilot" Sent: Wednesday, March 02, 2011 12:31 AM Subject: Zenith701801-List: Control Issues in Phase 1 testing u > > > I now have 16 hours on my 701 and I've found a few issues that are > curious, to say the least. > > > Second, I'm following the AC 90-89A guide for test-flying my airplane. > I'm conducting the "Lateral-directional Stability Control Tests" described > on page 51 of this document. I've found the rudder will not spring back > to neutral in flight but will instead maintain its last set position, even > at near full deflection! I think it's because there is no vertical > stabilizer and there's a lot of rudder surface area ahead of the rudder > hinge. I'm concerned a full deflection, especially near maneuvering > speed, may cause a control lock in full rudder deflection. > Has anyone else noticed these issues in their aircraft? > > Thanks, > > Dan Ginty > N787DG > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=332451#332451 > > > ________________________________ Message 5 _____________________________________ Time: 02:49:05 PM PST US From: "fritz" Subject: Re: Zenith701801-List: Control Issues in Phase 1 testing I elected to do away with my V noch on the 701--- have you folks looked close on how much the V notch makes the support plate flex? Much smoother rudder action without the notch. Fritz ----- Original Message ----- From: "Carl" Sent: Wednesday, March 02, 2011 4:50 PM Subject: Re: Zenith701801-List: Control Issues in Phase 1 testing > > Dan > I believe the V blocks on the nose gear bearing are designed to return the > rudder to the neutral position in flight to act as a fin and provide > directional stability. Unfortunately they are not always effective if the > rudder control system has a lot of friction; and the system does have a > lot of friction. You may want to try and reduce friction and check if your > blocks are optimized.. > In my case, since the blocks did not seam to help much and had to keep my > feet on the pedals all the time, I installed a nose wheel steering > disconnect to reduce the friction. in flight. This makes the rudder > control lighter and spares the legs on long flights. The rudder pretty > much acts as it did before; when deflected up to two ball width, it stays > deflected. and needs to be returned ,even with the reduced friction in my > system. This shows that the a|c minus rudder has close to 0 stability; > that being the case there is no aerodynamic force to return the rudder to > neutral so it stays aligned with the airflow. > In cruise, I found that once the a|c is in trim and the rudder is in > neutral just using the pedals as foot rest gives a pretty comfortable ride > even in light turbulence. In that situation the rudder becomes a big fin > and for a small, a|c gives good directional stability. > I experimented by adding a ventral fin (about two 2 sqf). It did little > for stability in the air but made the aircraft much more difficult to turn > downwind on the water (I`m on floats).So it came off.and is now a > conversation item on the wall in my hangar. > As to your concern about rudder lock, my testing with floats (they make > the a|c less directionally stable) I find that the rudder becomes harder > to deflect from neutral : > 1- the further it is deflected: and > 2 -the higher the IAS. > I must emphasise that I have not conducted this test at any where close to > manoeuvring speed but I doubt a rudder lock could happen. > In summary. the testing I have done leads me to believe the rudder is > effective and when used properly control the a|c in all normal manoeuvres. > Since the rudder is also a large part of the fin area, I expect the loss > of same would render the a|c uncontrollable. So I check rudder very > closely before flight. > Carl > ays > ----- Original Message ----- > From: "txpilot" > To: > Sent: Wednesday, March 02, 2011 12:31 AM > Subject: Zenith701801-List: Control Issues in Phase 1 testing > u > >> >> >> I now have 16 hours on my 701 and I've found a few issues that are >> curious, to say the least. >> >> >> Second, I'm following the AC 90-89A guide for test-flying my airplane. >> I'm conducting the "Lateral-directional Stability Control Tests" >> described on page 51 of this document. I've found the rudder will not >> spring back to neutral in flight but will instead maintain its last set >> position, even at near full deflection! I think it's because there is no >> vertical stabilizer and there's a lot of rudder surface area ahead of the >> rudder hinge. I'm concerned a full deflection, especially near >> maneuvering speed, may cause a control lock in full rudder deflection. >> Has anyone else noticed these issues in their aircraft? >> >> Thanks, >> >> Dan Ginty >> N787DG >> >> >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=332451#332451 >> >> >> >> >> >> >> >> >> >> >> > > > ________________________________ Message 6 _____________________________________ Time: 08:33:39 PM PST US From: JohnDRead@aol.com Subject: Re: Zenith701801-List: Control Issues in Phase 1 testing Re: bending the elevator. There was a note from Zenith that described cutting a grove down a piece of 2 x 4 to fit the trailing edge and then to bend the edge up. A call to the factory would verify. Regards, John CH701 - Colorado - Jabiru 3300 Cell: 719-494-4567 Home: 303-648-3261 In a message dated 3/2/2011 6:13:49 A.M. Mountain Standard Time, klondike@megalink.net writes: --> Zenith701801-List message posted by: "fritz" Dan-- Sounds like you still have the bend at the trailing edge of the elevator. Many moons ago, Chris said to take the bend out. Fritz ----- Original Message ----- From: "txpilot" Sent: Wednesday, March 02, 2011 12:31 AM Subject: Zenith701801-List: Control Issues in Phase 1 testing > > > I now have 16 hours on my 701 and I've found a few issues that are > curious, to say the least. > > First, it seems the aircraft cannot be trimmed for level flight with the > flaps down. Although the elevator trim is neutral or slightly down in > cruise with the flaps up, no amount of up elevator trim will prevent the > airplane from nose-diving (HARD) with the flaps down. > > Second, I'm following the AC 90-89A guide for test-flying my airplane. > I'm conducting the "Lateral-directional Stability Control Tests" described > on page 51 of this document. I've found the rudder will not spring back > to neutral in flight but will instead maintain its last set position, even > at near full deflection! I think it's because there is no vertical > stabilizer and there's a lot of rudder surface area ahead of the rudder > hinge. I'm concerned a full deflection, especially near maneuvering > speed, may cause a control lock in full rudder deflection. > > Third, I conducted the "Spiral Stability" check described in the same > Advisory Circular. To my surprise, the aircraft maintains neutral > stability (i.e. - it will not return from a banked condition to level > flight). This is not typical of high wing aircraft. Although this is not > a critical safety issue, it does make the airplane a little more difficult > to fly. > > Has anyone else noticed these issues in their aircraft? > > Thanks, > > Dan Ginty > N787DG > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=332451#332451 > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith701801-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith701801-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith701801-list Browse Digests http://www.matronics.com/digest/zenith701801-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.