Today's Message Index:
----------------------
1. 07:24 PM - Re: Zenith701801-List Digest: 2 Msgs - 06/09/12 (Dougnoble@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Zenith701801-List Digest: 2 Msgs - 06/09/12 |
hello
In a message dated 6/10/2012 12:07:37 A.M. Pacific Daylight Time,
zenith701801-list@matronics.com writes:
*
=================================================
Online Versions of Today's List Digest Archive
=================================================
Today's complete Zenith701801-List Digest can also be found in either of
the
two Web Links listed below. The .html file includes the Digest formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the Zenith701801-List Digest and can be viewed with a generic text
editor
such as Notepad or with a web browser.
HTML Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter
12-06-09&Archive=Zenith701801
Text Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter
2012-06-09&Archive=Zenith701801
===============================================
EMail Version of Today's List Digest Archive
===============================================
----------------------------------------------------------
Zenith701801-List Digest Archive
---
Total Messages Posted Sat 06/09/12: 2
----------------------------------------------------------
Today's Message Index:
----------------------
1. 07:26 AM - Re: Re: Elevator Skin, Not as expected (Perry Delano)
2. 08:22 AM - Re: Re: Elevator Skin, Not as expected (Dan Hill)
________________________________ Message 1
_____________________________________
Time: 07:26:56 AM PST US
From: "Perry Delano" <pdelano@telus.net>
Subject: RE: Zenith701801-List: Re: Elevator Skin, Not as expected
Hi all,
After getting a lot of good responses here and talking with Caleb at
zenith,
the solution to the miss measured skin (still not sure that is what it is
as
everthing seems right exept the top skin shy about 20 mm) is to cut the
short skin back to the trailing edge of the spar and slide a new piece
underneath it to the leading edge of the spar (maybe a little more in each
case to ensure edge distance),thus both pieces will overlap each other.
Prior to doing any cutting ensure the new piece is long enough, wide enough
and alligned, I'll match drill the new piece through the old piece (already
drilled) and that I will cut off. End result, one extra seam line, no extra
rivets, no drilling out all the rivets in the bottom side of the skin and
no
need to start from scratch on the elevator, "pheuuuww".
My challenge now is to find some .016 - .020 6061-T6 here on the west coast
or North West (US). Does anybody have a recommendation?
As an aside, I have gotten great support from Caleb at Zenith on too many
queries.
Regards,
Perry
________________________________ Message 2
_____________________________________
Time: 08:22:09 AM PST US
From: "Dan Hill" <dan@hillsgun.com>
Subject: RE: Zenith701801-List: Re: Elevator Skin, Not as expected
Hi Perry: I think you will find it easiest (and in the long run cheapest)
to
order it from aircraft spruce. I have sourced a few other local sources for
some raw materials, but for most part spruce has been the best supplier as
the service has been very good, and they know what you want when you order.
You can have the .016 rolled. Dan Hill 701 scratch builder.
-----Original Message-----
From: owner-zenith701801-list-server@matronics.com
[mailto:owner-zenith701801-list-server@matronics.com] On Behalf Of Perry
Delano
Sent: Saturday, June 09, 2012 7:26 AM
Subject: RE: Zenith701801-List: Re: Elevator Skin, Not as expected
--> <pdelano@telus.net>
Hi all,
After getting a lot of good responses here and talking with Caleb at
zenith,
the solution to the miss measured skin (still not sure that is what it is
as
everthing seems right exept the top skin shy about 20 mm) is to cut the
short skin back to the trailing edge of the spar and slide a new piece
underneath it to the leading edge of the spar (maybe a little more in each
case to ensure edge distance),thus both pieces will overlap each other.
Prior to doing any cutting ensure the new piece is long enough, wide enough
and alligned, I'll match drill the new piece through the old piece (already
drilled) and that I will cut off. End result, one extra seam line, no extra
rivets, no drilling out all the rivets in the bottom side of the skin and
no
need to start from scratch on the elevator, "pheuuuww".
My challenge now is to find some .016 - .020 6061-T6 here on the west coast
or North West (US). Does anybody have a recommendation?
As an aside, I have gotten great support from Caleb at Zenith on too many
queries.
Regards,
Perry
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|