Today's Message Index:
----------------------
1. 07:42 AM - Fw: Kolb-List: wiring 912 uls (frank goodnight)
2. 01:15 PM - Re: Fw: Kolb-List: wiring 912 uls (rayj)
3. 05:51 PM - Re: Fw: Kolb-List: wiring 912 uls (Curt Thompson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Fw: Kolb-List: wiring 912 uls |
----- Forwarded Message ----
From: frank goodnight <frank.goodnight@att.net>
Sent: Wed, January 16, 2013 9:38:49 AM
Subject: Kolb-List: wiring 912 uls
Need help understanding the 912 uls generating sys.
looking at page 17-1 fig 29 of the rotax install manual. I need to know if i can
check for voltage between one of the yellow (ge) wires and ground, or between
the two yellow wires , and if so what should the voltage be.
What does the 2,5 and a little square box repesent
in the wires going to the G terminals on the rectifier?
What is # 11 in fig 29 if it is a diode , what kind and where can i find one.
my engine was removed from a wrecked plane and i don't
think the hookup used the capaciator or whatever #11 is
that is shown in fig 29. thanks to anyone that can help me.
Frank Goodnight
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Fw: Kolb-List: wiring 912 uls |
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Fw: Kolb-List: wiring 912 uls |
Frank,
You must have a different install manual than me. I think the latest is
"d04967.pdf" dated "Ed.2, Rev.0 Aug 1, 2012". I got it from here:
http://www.rotax-owner.com/support-bulletin/engine-manuals
Those yellow wires are probably AC signals. A note in my install manual
says:
"Approx . 250 W AC output at 5800 rpm. For DC."
I can't find the same figure as you.
My manual says that there should be a 22000uF/25V capacitor on the "R",
"+B", and "C" pins of the rectifier/regulator to ground. The regulator will
fail should the battery get disconnected while running.
Curt
From: owner-zenith701801-list-server@matronics.com
[mailto:owner-zenith701801-list-server@matronics.com] On Behalf Of frank
goodnight
Sent: Wednesday, January 16, 2013 7:42 AM
Subject: Zenith701801-List: Fw: Kolb-List: wiring 912 uls
----- Forwarded Message ----
From: frank goodnight <frank.goodnight@att.net>
Sent: Wed, January 16, 2013 9:38:49 AM
Subject: Kolb-List: wiring 912 uls
Need help understanding the 912 uls generating sys.
looking at page 17-1 fig 29 of the rotax install manual. I need to know if i
can check for voltage between one of the yellow (ge) wires and ground, or
between the two yellow wires , and if so what should the voltage be.
What does the 2,5 and a little square box repesent
in the wires going to the G terminals on the rectifier?
What is # 11 in fig 29 if it is a diode , what kind and where can i find
one.
my engine was removed from a wrecked plane and i don't
think the hookup used the capaciator or whatever #11 is
that is shown in fig 29. thanks to anyone that can help me.
Frank Goodnight
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|