---------------------------------------------------------- Zenith750-List Digest Archive --- Total Messages Posted Wed 11/12/08: 2 ---------------------------------------------------------- Today's Message Index: ---------------------- 0. 12:21 AM - Please Make A Contribution To Support Your Lists (Matt Dralle) 1. 02:30 PM - Re: Zenith750-List Digest: 3 Msgs - 11/11/08 (silverbirch1@netzero.net) ________________________________ Message 0 _____________________________________ Time: 12:21:53 AM PST US From: Matt Dralle Subject: Zenith750-List: Please Make A Contribution To Support Your Lists Dear Listers, There is no advertising income to support the Matronics Email Lists and Forums. The operation is supported 100% by your personal Contributions during the November Fund Raiser. Please make your Contribution today to support the continued operation and upgrade of these services. You can pick up a really nice gift for making your Contribution too! You may use a Credit Card or Paypal at the Matronics Contribution Site here: http://www.matronics.com/contribution or, you can send a personal check to the following address: Matronics / Matt Dralle PO Box 347 Livermore, CA 94551-0347 Thank you in advance for your generous support! Matt Dralle Matronics Email List and Forum Administrator ________________________________ Message 1 _____________________________________ Time: 02:30:53 PM PST US From: "silverbirch1@netzero.net" Subject: Zenith750-List: Re: Zenith750-List Digest: 3 Msgs - 11/11/08 Stefan, -- I am building a CH750 from a kit. I have built on the horizo ntal stabilizer. In fitting the skin I found that the cutouts for the f ront brackets were about 10mm too far apart. They need to be trimmed in board about 4mm each to fit over the front brackets. I have also built up the elevator and trim tab. The manual discusses wh ere to drill and mount the horn angle (75T3-6) in the elevator skeleton section (75-TA3), page 6. The exact location of the horn angle on the s par is critical since it must be flush with the upper horn (75T3-7) and lower horn (75TA-8). The upper and lower horns are predrilled. If the horn angle is already drilled to A5, as instructed, there is little room for adjustment when attaching the elevator horns. The horns should lik ely be clecoed to the skeleton and the horn angle positioned before the horn angle is drilled, at least to A5 size. Thank you for your web site Stefan. _____________________________________________________________ Compete with the big boys. Click here to find products to benefit your business. http://thirdpartyoffers.netzero.net/TGL2221/fc/Ioyw6i4t3HXJcvgIbKSZUqXpT RVjHPcBmXw6xXPbvjV17Kbc39vQHU/?count=1234567890 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith750-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith750-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith750-list Browse Digests http://www.matronics.com/digest/zenith750-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.