----------------------------------------------------------
                           Zenith750-List Digest Archive
                                      ---
                     Total Messages Posted Sun 05/10/09: 2
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 10:20 AM - "L"  (Bruce Cruikshank)
     2. 06:38 PM - Re: Standard L angle dimensions  (Joe Harrington)
 
 
 
________________________________  Message 1  _____________________________________


Time: 10:20:50 AM PST US
From: "Bruce Cruikshank" <n19z@dslextreme.com>
Subject: Zenith750-List: "L"

Joe,

Just measured the L that came with my kit.

It is 19 X 19 mm X .025"

b/c

________________________________  Message 2  _____________________________________


Time: 06:38:46 PM PST US
From: Joe Harrington <cicrn@telus.net>
Subject: Re: Zenith750-List: Standard L angle dimensions


Thanks Craig and Bruce!

For the life of me, I can't see where the dimensions are shown in the  
plans. No matter, thanks to you guys, I will keep plodding along.

Regards,
Joe
CH750 scratch building

On 8-May-09, at 11:52 PM, Craig Payne wrote:

>
> <craig@craigandjean.com>
>
> I only have the 701 and 601XL plans but look on some of the first  
> pages of
> the plans. The width before bending (Developed Length) is 36 mm and  
> is bent
> from 0.025 inch sheet. Bend with a radius of 1/8th inch. They are  
> generally
> made across the full width of a 4 foot sheet so are called out with  
> a length
> of 1219 mm. I wrote an article on a simple press brake made out of  
> 2 by 4s
> and C-clamps for bending these if you want it. It was in the Zenith
> newsletter a few issues ago.
>
> -- Craig
>
> -----Original Message-----
> From: owner-zenith750-list-server@matronics.com
> [mailto:owner-zenith750-list-server@matronics.com] On Behalf Of Joe
> Harrington
> Sent: Friday, May 08, 2009 11:44 PM
> To: Zenith 750 List
> Subject: Zenith750-List: Standard L angle dimensions
>
>
> Hi,
>
> The assembly manual refers to using some standard L angle aluminum. I
> have looked through the plans, assembly manual, construction
> standards but can't see what the dimensions are. Is it 20mm flanges x
> 0.025"? Or what? Thanks in advance.
>
> Joe
> 750 Scratch Build
>
>


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               zenith750-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Zenith750-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/zenith750-list
Browse Digests                   http://www.matronics.com/digest/zenith750-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.