Today's Message Index:
----------------------
 
     1. 01:56 PM - test (joe motis)
     2. 02:57 PM - Mistake in plans wings CH 750? (joe motis)
     3. 04:06 PM - Fw: Possible mistake upper spar cap CH 750 75-W-2 Illustration 2 	Angle dimension given is 40 mm should be 52 mm? (joe motis)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
01:56:19 PM PST US
Subject: 
test
From: 
joe motis <joemotis@gmail.com>
      
      no archives
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
02:57:01 PM PST US
Subject: 
Mistake in plans wings CH 750?
From: 
joe motis <joemotis@gmail.com>
      
      I am building the wing spars and I made both upper spar caps with a 40 mm
      diimension on the angle cut end. It does not fit the way it is supposed to.
      The actual measurement needs to be 52 mm. I am working off my first set of
      plans and the second set (upgraded) are down at the hangar so maybe this
      mistake has been caught in the next set.
      Anyone else have this issue?.
      Page 75-W-2 Illustration 2 Upper spar cap
      
      Thanks
      Joe Motis
      CH 750 WW Corvair
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
04:06:15 PM PST US
Subject: 
Fwd: Possible mistake upper spar cap CH 750 75-W-2 Illustration
      2  	Angle dimension given is 40 mm should be 52 mm?
From: 
joe motis <joemotis@gmail.com>
      
      ---------- Forwarded message ----------
      From: joe motis <joemotis@gmail.com>
      Subject: Fwd: Possible mistake upper spar cap CH 750 75-W-2 Illustration 2
      Angle dimension given is 40 mm should be 52 mm?
      
      
      Hi Listers,
      
      I am building the wing spars and I made both upper spar caps with a 40 mm
      diimension on the angle cut end. It does not fit the way it is supposed to.
      The actual measurement needs to be 52 mm. The 80 mm up and 272 mm
      over dimension have both been checked and are correct for the spar angle.
      
      
      Anyone else have this issue?.
      Page 75-W-2 Illustration 2 Upper spar cap
      
      Thanks
      Joe Motis
      CH 750 WW Corvair
      








Other Matronics Email List Services




Post A New Message
  
zenith750-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Zenith750-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/zenith750-list
Browse Zenith750-List Digests
  
http://www.matronics.com/digest/zenith750-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --