Today's Message Index:
----------------------
1. 04:54 AM - Re: Fw: Possible mistake upper spar cap CH 750 75-W-2 Illustration 2 Angle dimension given is 40 mm should be 52 mm? (Art Olechowski)
2. 06:04 AM - Possible mistake upper spar cap CH 750 ----SPAR CAP RIVET SPACING (fritz)
3. 06:09 AM - 750 scratch buliders (fritz)
4. 04:12 PM - Re: 750 scratch buliders (Art Olechowski)
5. 04:51 PM - Re: 750 scratch buliders (fritz)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Fwd: Possible mistake upper spar cap CH 750 75-W-2 |
Illustration 2 Angle dimension given is 40 mm should be 52 mm?
Joe,
Great catch and likely only something a scratch builder would have caught.
- I'm not as far a long as you are but I've made note to cut the upper sp
ar cap angle using the web as the guide.- Thank you for passing along you
r finding.
Art
Wichita, KS
do not archive
-
--- On Sun, 2/7/10, joe motis <joemotis@gmail.com>wrote:
From: joe motis <joemotis@gmail.com>
Subject: Zenith750-List: Fwd: Possible mistake upper spar cap CH 750 75-W-2
Illustration 2 Angle dimension given is 40 mm should be 52 mm?
=0A---------- Forwarded message ----------
From: joe motis <joemotis@gmail.com>
=0ASubject: Fwd: Possible mistake upper spar cap CH 750 75-W-2 Illustration
2 Angle dimension given is 40 mm should be 52 mm?
Hi Listers,
=0A=0A
I am building the wing spars and I made both upper spar caps with a 40 mm d
iimension on the angle cut end. It does not fit the way it is supposed to.
The actual measurement needs to be 52 mm. The 80 mm up and 272 mm over-di
mension have both been checked and are correct for the spar angle. =0A
Anyone else have this issue?.
Page 75-W-2 Illustration 2 Upper spar cap
-
Thanks
Joe Motis
CH 750 WW Corvair
=0A
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Possible mistake upper spar cap CH 750 ----SPAR CAP RIVET |
SPACING
also there is a mistake in the spar caps rivet spacing
Fritz
----- Original Message -----
From: joe motis
To: zenith750-list@matronics.com
Sent: Sunday, February 07, 2010 6:11 PM
Subject: Zenith750-List: Fwd: Possible mistake upper spar cap CH 750
75-W-2 Illustration 2 Angle dimension given is 40 mm should be 52 mm?
---------- Forwarded message ----------
From: joe motis <joemotis@gmail.com>
Date: Sun, Feb 7, 2010 at 3:09 PM
Subject: Fwd: Possible mistake upper spar cap CH 750 75-W-2
Illustration 2 Angle dimension given is 40 mm should be 52 mm?
To: joe motis <joemotis@gmail.com>
Hi Listers,
I am building the wing spars and I made both upper spar caps with a 40
mm diimension on the angle cut end. It does not fit the way it is
supposed to. The actual measurement needs to be 52 mm. The 80 mm up and
272 mm over dimension have both been checked and are correct for the
spar angle.
Anyone else have this issue?.
Page 75-W-2 Illustration 2 Upper spar cap
Thanks
Joe Motis
CH 750 WW Corvair
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 750 scratch buliders |
Joe & Art & ?????
How many folks scrach building the 750, and how far along are you ?????
There seems to be "several mistakes" on even the updated plans------- I
have found several----------- it would be nice if we contacted each
other instead of each of us "reinventing the wheel"
Fritz------- scratch building CH 750
----- Original Message -----
From: Art Olechowski
To: zenith750-list@matronics.com
Sent: Sunday, February 07, 2010 11:18 PM
Subject: Re: Zenith750-List: Fwd: Possible mistake upper spar cap CH
750 75-W-2 Illustration 2 Angle dimension given is 40 mm should be 52
mm?
Joe,
Great catch and likely only something a scratch builder would
have caught. I'm not as far a long as you are but I've made note to cut
the upper spar cap angle using the web as the guide. Thank you for
passing along your finding.
Art
Wichita, KS
do not archive
--- On Sun, 2/7/10, joe motis <joemotis@gmail.com>wrote:
From: joe motis <joemotis@gmail.com>
Subject: Zenith750-List: Fwd: Possible mistake upper spar cap
CH 750 75-W-2 Illustration 2 Angle dimension given is 40 mm should be 52
mm?
To: zenith750-list@matronics.com
Date: Sunday, February 7, 2010, 5:11 PM
---------- Forwarded message ----------
From: joe motis <joemotis@gmail.com>
Date: Sun, Feb 7, 2010 at 3:09 PM
Subject: Fwd: Possible mistake upper spar cap CH 750 75-W-2
Illustration 2 Angle dimension given is 40 mm should be 52 mm?
To: joe motis <joemotis@gmail.com>
Hi Listers,
I am building the wing spars and I made both upper spar caps
with a 40 mm diimension on the angle cut end. It does not fit the way it
is supposed to. The actual measurement needs to be 52 mm. The 80 mm up
and 272 mm over dimension have both been checked and are correct for the
spar angle.
Anyone else have this issue?.
Page 75-W-2 Illustration 2 Upper spar cap
Thanks
Joe Motis
CH 750 WW Corvair
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 750 scratch buliders |
Fritz,
I have just begun laying out and cutting form blocks for the 750 and when n
ot doing that I'm working on a BOM to get an order placed.- Where are you
all getting your blind rivets from?
do not archive
Art
--- On Mon, 2/8/10, fritz <klondike@megalink.net> wrote:
From: fritz <klondike@megalink.net>
Subject: Zenith750-List: 750 scratch buliders
=0A=0A =0A =0A=0AJoe & Art & ?????=0AHow many folks scrach building the 750
, and how far along are you =0A?????- There seems to be "several mistakes
" on even the updated =0Aplans-------- I have found several----------- it
would be nice if we =0Acontacted each other instead of each of us "reinven
ting the wheel"=0AFritz------- scratch building CH 750=0A=0A ----- Origina
l Message ----- =0A From: =0A Art =0A Olechowski =0A To: zenith750-list
@matronics.com =0A =0A Sent: Sunday, February 07, 2010 11:18 =0A PM=0A
Subject: Re: Zenith750-List: Fwd: =0A Possible mistake upper spar cap CH 7
50 75-W-2 Illustration 2 Angle dimension =0A given is 40 mm should be 52 m
m?=0A
=0A =0A =0A =0A Joe,
Great catch and likely only something a scratch =0A builder would ha
ve caught.- I'm not as far a long as you are but =0A I've made not
e to cut the upper spar cap angle using the web as the =0A guide.-
Thank you for passing along your finding.
Art =0A
Wichita, KS
do not archive
-
--- On Sun, =0A 2/7/10, joe motis <joemotis@gmail.com>wrote:
=0A
From: =0A joe motis <joemotis@gmail.com>
Subject: =0A Zenith750-List: Fwd: Possible mistake upper spar cap
CH 750 75-W-2 =0A Illustration 2 Angle dimension given is 40 mm sh
ould be 52 mm?
=0A
=0A ---------- Forwarded message =0A ----------
From: joe motis <joemotis@gmail.com>
Subject: Fwd: Possible mistake upper =0A spar cap CH 750 75-W-2 Il
lustration 2 Angle dimension given is 40 mm =0A should be 52 mm?
Hi =0A Listers,
=0A
I am building the wing spars and I made =0A both upper spar caps w
ith a 40 mm diimension on the angle cut end. It =0A does not fit t
he way it is supposed to. The actual measurement needs =0A to be 5
2 mm. The 80 mm up and 272 mm over-dimension have both =0A been
checked and are correct for the spar angle. =0A
Anyone else have this issue?.
Page 75-W-2 =0A Illustration 2 Upper spar cap
-
Thanks
Joe Motis
CH 750 WW Corvair =0A
href="http://www.matronics.com/Navigator?Zenith750-List">http://www.matro
nics.com/Navigator?Zenith750-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/c
=0A=0A=0A
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 750 scratch buliders |
Art--- I buy all my blind rivets from ZAC-------- I feel better buying
from ZAC, as they purchase from realiable sources.
Form blocks----- double check measurements of heigth of elev spar to
forming blocks for the elev. ribs.
Art-- drop me a line back channel so I can "talk" directly to you.
Where are you located.
Friz------scratch building 750----------do not archive
----- Original Message -----
From: Art Olechowski
To: zenith750-list@matronics.com
Sent: Monday, February 08, 2010 7:10 PM
Subject: Re: Zenith750-List: 750 scratch buliders
Fritz,
I have just begun laying out and cutting form blocks for the 750
and when not doing that I'm working on a BOM to get an order placed.
Where are you all getting your blind rivets from?
do not archive
Art
--- On Mon, 2/8/10, fritz <klondike@megalink.net> wrote:
From: fritz <klondike@megalink.net>
Subject: Zenith750-List: 750 scratch buliders
To: zenith750-list@matronics.com
Date: Monday, February 8, 2010, 8:08 AM
Joe & Art & ?????
How many folks scrach building the 750, and how far along are
you ????? There seems to be "several mistakes" on even the updated
plans------- I have found several----------- it would be nice if we
contacted each other instead of each of us "reinventing the wheel"
Fritz------- scratch building CH 750
----- Original Message -----
From: Art Olechowski
To: zenith750-list@matronics.com
Sent: Sunday, February 07, 2010 11:18 PM
Subject: Re: Zenith750-List: Fwd: Possible mistake upper
spar cap CH 750 75-W-2 Illustration 2 Angle dimension given is 40 mm
should be 52 mm?
Joe,
Great catch and likely only something a scratch
builder would have caught. I'm not as far a long as you are but I've
made note to cut the upper spar cap angle using the web as the guide.
Thank you for passing along your finding.
Art
Wichita, KS
do not archive
--- On Sun, 2/7/10, joe motis
<joemotis@gmail.com>wrote:
From: joe motis <joemotis@gmail.com>
Subject: Zenith750-List: Fwd: Possible mistake upper
spar cap CH 750 75-W-2 Illustration 2 Angle dimension given is 40 mm
should be 52 mm?
To: zenith750-list@matronics.com
Date: Sunday, February 7, 2010, 5:11 PM
---------- Forwarded message ----------
From: joe motis <joemotis@gmail.com>
Date: Sun, Feb 7, 2010 at 3:09 PM
Subject: Fwd: Possible mistake upper spar cap CH 750
75-W-2 Illustration 2 Angle dimension given is 40 mm should be 52 mm?
To: joe motis <joemotis@gmail.com>
Hi Listers,
I am building the wing spars and I made both upper
spar caps with a 40 mm diimension on the angle cut end. It does not fit
the way it is supposed to. The actual measurement needs to be 52 mm. The
80 mm up and 272 mm over dimension have both been checked and are
correct for the spar angle.
Anyone else have this issue?.
Page 75-W-2 Illustration 2 Upper spar cap
Thanks
Joe Motis
CH 750 WW Corvair
href="http://www.matronics.com/Navigator?Zenith750-List">http://www.mat
ronics.com/Navigator?Zenith750-Listhref="http://forums.matronics.com">h
ttp://forums.matronics.comhref="http://www.matronics.com/contribution">
http://www.matronics.com/chttp://www.m
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|