Today's Message Index:
----------------------
1. 10:48 AM - Horz Relief Angle (Art Olechowski)
2. 11:04 AM - Re: Horz Relief Angle (Curt Thompson)
3. 06:49 PM - Re: Horz Relief Angle (Art Olechowski)
4. 07:38 PM - Re: Horz Relief Angle (Curt Thompson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Horz Relief Angle |
Hey all you 750 scratchbuilders,
For the-Horz form block-reliefs, what relief angle have you all had suc
ess with to obtain a semi-flat horz tip rib?--I have 10deg of angle for
springback (tried 6deg), should I try 15deg for the reliefs?
-
Thanks in advance.
-
do not archive
ch750 v2
Art
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Horz Relief Angle |
Art,
Like you, I started with 6 degrees on my CH701. I found that 10 degrees
worked better. I still had to tweak the angle a bit after the part came out
of the form block.
Curt
_____
From: owner-zenith750-list-server@matronics.com
[mailto:owner-zenith750-list-server@matronics.com] On Behalf Of Art
Olechowski
Sent: Thursday, September 09, 2010 10:46 AM
Subject: Zenith750-List: Horz Relief Angle
Hey all you 750 scratchbuilders,
For the Horz form block reliefs, what relief angle have you all had sucess
with to obtain a semi-flat horz tip rib? I have 10deg of angle for
springback (tried 6deg), should I try 15deg for the reliefs?
Thanks in advance.
do not archive
ch750 v2
Art
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Horz Relief Angle |
Cool Curt thanks for your response. 10 degrees is what I have for springbac
k of the .025 on the flange springback for the horz tip rib but what about
the flute reliefs? I surely won'tt want to use the same angle.- I was loo
king for something that actually works for flute angle for the material thi
ckness.- Be advise I realize this is a as needed purpose relief angle and
was thinking 15deg was good.- Just looking for on purpose flute angle .
do not archive
ch750 v2
Art
--- On Thu, 9/9/10, Curt Thompson <charlievictor102@hotmail.com> wrote:
From: Curt Thompson <charlievictor102@hotmail.com>
Subject: RE: Zenith750-List: Horz Relief Angle
=0A=0A=0A =0A =0A=0A=0A=0A=0A=0A=0A=0AArt, =0A=0A - =0A=0ALike you, I sta
rted with 6 degrees on my=0ACH701.- I found that 10 degrees worked better
.- I still had to tweak the angle=0Aa bit after the part came out of the
form block. =0A=0A - =0A=0ACurt =0A=0A - =0A=0A=0A=0A=0A=0A=0A=0A=0A=0A
From:=0Aowner-zenith750-list-server@matronics.com=0A[mailto:owner-zenith750
-list-server@matronics.com] On Behalf Of Art Olechowski
=0ASent: Thursday, September 09, 2010=0A10:46 AM
=0ATo: Zenith750
=0ASubject: Zenith750-List: Horz=0ARelief Angle =0A=0A=0A=0A - =0A=0A=0A
=0A =0A =0A Hey all you 750 scratchbuilders, =0A =0A =0A For the-Ho
rz form block-reliefs, what=0A relief angle have you all had sucess with
to obtain a semi-flat horz tip=0A rib?--I have 10deg of angle for spr
ingback (tried 6deg), should I=0A try 15deg for the reliefs? =0A =0A =0A
- =0A =0A =0A Thanks in advance. =0A =0A =0A - =0A =0A =0A d
o not archive =0A =0A =0A ch750 v2 =0A =0A =0A Art =0A =0A =0A =0A
=0A=0A - -http://www.matronics.com/Navigator?Zenith750-Listhttp://forum
s.matronics.comhttp://www.matronics.com/contribution - =0A=0A=0A=0A=0A=0A
- List Contribution Web Site -
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Horz Relief Angle |
Art,
I used a 1 inch spindle sander to notch for the flutes. I have a note on
one of my wing nose rib form blocks that says I angled them at 45 degrees.
I still used fluting pliers once I got close.
Curt
_____
From: owner-zenith750-list-server@matronics.com
[mailto:owner-zenith750-list-server@matronics.com] On Behalf Of Art
Olechowski
Sent: Thursday, September 09, 2010 6:40 PM
Subject: RE: Zenith750-List: Horz Relief Angle
Cool Curt thanks for your response. 10 degrees is what I have for springback
of the .025 on the flange springback for the horz tip rib but what about the
flute reliefs? I surely won'tt want to use the same angle. I was looking
for something that actually works for flute angle for the material
thickness. Be advise I realize this is a as needed purpose relief angle and
was thinking 15deg was good. Just looking for on purpose flute angle .
do not archive
ch750 v2
Art
--- On Thu, 9/9/10, Curt Thompson <charlievictor102@hotmail.com> wrote:
From: Curt Thompson <charlievictor102@hotmail.com>
Subject: RE: Zenith750-List: Horz Relief Angle
Art,
Like you, I started with 6 degrees on my CH701. I found that 10 degrees
worked better. I still had to tweak the angle a bit after the part came out
of the form block.
Curt
_____
From: owner-zenith750-list-server@matronics.com
[mailto:owner-zenith750-list-server@matronics.com] On Behalf Of Art
Olechowski
Sent: Thursday, September 09, 2010 10:46 AM
Subject: Zenith750-List: Horz Relief Angle
Hey all you 750 scratchbuilders,
For the Horz form block reliefs, what relief angle have you all had sucess
with to obtain a semi-flat horz tip rib? I have 10deg of angle for
springback (tried 6deg), should I try 15deg for the reliefs?
Thanks in advance.
do not archive
ch750 v2
Art
http://www.matronics.com/Navigator?Zenith750-List
http://forums.matronics.com
http://www.matronics.com/contribution
http://www.matronics.com/contribution
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|