Do my best sir...
Smokey
--- On Tue, 10/7/08, Jim Stone <jrstone@insightbb.com> wrote:
From: Jim Stone <jrstone@insightbb.com>
Subject: Re: Airfilter problem
To: rocket-list@matronics.com
Date: Tue, 7 Oct 2008 10:09:26 AM PDT
#yiv1338319602 DIV {
MARGIN:0px;}
Smokey,
If you happen to have that K&N model number,
you might save me from ordering the wrong one.
Thanks,
Jim
HR2
----- Original Message -----
From:
Smoky
Ray
To: rocket-list@matronics.com
Sent: Monday, October 06, 2008 7:42
PM
Subject: Re: Airfilter
problem
Jim,
-
- I'm using a K&N cone filter on my Harmon intake w/bypass, 3.5
inch top. Works great with my Skytech starter and clears the cowl with 2"
to
spare. Suprisingly, K&N had compettive prices...
-
Smokey
HR2
-----
Original Message ----
From: Jim Stone <jrstone@insightbb.com>
To: rocket-list@matronics.com
Sent:
Monday, October 6, 2008 6:42:56 PM
Subject: Re: Airfilter
problem
Hey Tom,
Been doing some research on filters.- Your
part number was close but I came up with RB-0910 which is 5 inches high,
and
an RB-0900 which is 4 inches in height.- Do you think the 4 inch high o
ne
would work better, i.e., less contact with cowl and starter?
I also found some cone shapes which are about 5
inches high but have 3 1/2 inch diameter top, perhaps that would work, wh
at do
you think?
I wish my cowl was off so I could take some
measurements.- I just put it back on Sunday after the annual
inspection.
Jim Stone
Louisville KY
----- Original Message -----
From: Tom
Martin
To: rocket-list@matronics.com
Sent: Thursday, October 02, 2008 10:53
AM
Subject: RE: Airfilter
problem
Jim
-----------
I had a similar set up on my second Harmon. -I used a conical K&N
filter that had a bit of an offset in the attach flange. -Part # RB
091.-- It did touch the starter and I put a big gob of RTV at the
point of contact. -It also tended to touch the cowling but never seem
ed
to cause and damage. -I do not see any reason why you could not squee
ze
a bit to get more clearance.- It is a nice simple
system.
-
Tom
Martin
-
From:
owner-rocket-list-server@matronics.com
[mailto:owner-rocket-list-server@matronics.com] On Behalf Of Jim Stone
Sent: October 2, 2008 10:39
AM
To:
rocket-list@matronics.com
Subject: Airfilter
problem
-
HR guys,
As per John Harmon's
recommendation, I have been using a UNI filter UP-6300 ast motorcycle
filter.- Not only do I not like the looks of the thing but it lays on
the inside of the cowl and has to deform a bit to do that, it also is
wearing where the cuff slides over the Y-valve.- I am using John's
intake Y valve and the angle of the filter side may not be quite
right.- Has anyone had this problem and or have a solution?-
Perhaps going to a K&N filter will do it, any model numbers would help
my search for a solution.
Thanks,
Jim
Stone - - -Checked by AVG.
Checked by AVG.
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/Navigator?Rocket-List"'>http://www.matr
onics.com/Navigator?Rocket-List
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://forums.matronics.com"'>http://forums.matronics.com
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/contribution"'>http://www.matronics.com
/contribution
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
=0A=0A=0A
