Chris,
For the total seal mod on the M14P contact bill Blackwell 623-703-1001
Best,
Doug
On Fri, Nov 20, 2009 at 12:53 PM, Chris Wise <wise@txc.net.au> wrote:
> Doug,
>
> I am interested in these Total seal pistons and rings that you mention.
>
> What is the big benefit of these rings and pistons versus factory parts?
> Are they available for the M14P engines and at what cost?
>
> Thanks,
> Chris.
>
> ----- Original Message -----
> *From:* doug sapp <dougsappllc@gmail.com>
> *To:* yak-list@matronics.com
> *Sent:* Saturday, November 21, 2009 3:23 AM
> *Subject:* Re: Re: The future of Nanchangs?
>
> Listers and lurkers,
> The days of 10 to 15K HS6A 1st or 2nd overhauled engines are long over.
> Look forward to 20 to 25K pricing by spring (if they are even
> available). A 9 to 10K top overhaul (parts only) is looking like the best
> and most cost effective way to go since most of the lower ends are still in
> pretty good shape and are designed to run 2000 to 2500 hours even on Chinese
> oils. A top overhaul installed with the Total Seal pistons and rings would
> breath new life (and a bit more hp) into the 1st and second overhaul engines
> now in service. We plan to be stocking top overhaul kits by spring of 2010.
>
>
> Barry is correct about the R985 being too heavy, but there are other
> engines out there, like the M462RF (I am installing one right now), the
> AI14, and the M14B (not P) just to name a few, but there simply is no 0 time
> 10 to 15K engines out there to be had. I have one NEW HS6A engine which I
> bought several years ago in a group of overhauled engines, we have installed
> the Total Seal rings in it and am holding it in reserve in case the R462RF
> engine does not work out. This engine will be for sale in the spring if all
> goes well with the 462 installation. I know of no other HS6A new or
> overhauled engines for sale in the US at this writing.
>
> Mag coils are another concern, maybe more so than replacement engine issue
> as the supply in Russia is near 0, China is nearly out and it's factory is
> shut down, it is reported that Europe has near 0 stock. To this end we are
> in the process of contracting with a US manufacturer to do a small
> production run. When they become available I would highly recommend that
> everyone stock at least one coil as a spare because based on the world wide
> reports of existing inventories I fully expect the first run to be sold out
> maybe even before it is produced. A second run is not possible until fall
> of 2011.
>
> All the best from Omak,
> Doug and Kathleen Sapp
>
>
> On Fri, Nov 20, 2009 at 7:57 AM, barryhancock <
> bhancock@worldwidewarbirds.com> wrote:
>
>> bhancock@worldwidewarbirds.com>
>>
>> Pappy, you speak blasphemy!!! If it ain't round, stay on the ground,
>> brother! [Wink]
>>
>> We have done a rough engineering study on putting a 985 on a CJ and it
>> just doesn't work. You could get around the fact that the engine is 6"
>> bigger in diameter, but the weight is just too much more. You'd be better
>> off throwing that R&D into domestic overhaul capabilities for the Housai.
>>
>> Happy Flying,
>>
>> Barry
>>
>> --------
>> Barry Hancock
>> Worldwide Warbirds, Inc.
>> www.worldwidewarbirds.com
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=273968#273968
>>
>>
>>
>>
>>
>>
>>
>> ==========
>> ="_blank">www.aeroelectric.com
>> ooks.com" target="_blank">www.buildersbooks.com
>> et="_blank">www.homebuilthelp.com
>> ="_blank">http://www.matronics.com/contribution
>> le, List Admin.
>> ==========
>> rget="_blank">http://www.matronics.com/Navigator?Yak-List
>> ==========
>> http://forums.matronics.com
>> ==========
>>
>>
>>
>>
>
>
> --
> Maybe life is not the party that we were expecting,
> but in the mean time, we're here and we can still dance....."
> Douglas Sapp
> Doug Sapp LLC
> 18B Riverview Road
> Omak WA 98841
> PH 509-826-4610
> Fax 509-826-3644
>
> *
>
> href="http://www.aeroelectric.com">www.aeroelectric.com
> href="http://www.buildersbooks.com">www.buildersbooks.com
> href="http://www.homebuilthelp.com">www.homebuilthelp.com
> href="http://www.matronics.com/contribution">http://www.matronics.com/chref="http://www.matronics.com/Navigator?Yak-List">http://www.matronics.com/Navigator?Yak-List
> href="http://forums.matronics.com">http://forums.matronics.com
> *
>
> ------------------------------
> Release Date: 05/23/09 07:00:00
>
> *
>
> *
>
>
--
Maybe life is not the party that we were expecting,
but in the mean time, we're here and we can still dance....."
Douglas Sapp
Doug Sapp LLC
18B Riverview Road
Omak WA 98841
PH 509-826-4610
Fax 509-826-3644
