Today's Message Index:
----------------------
1. 07:05 AM - Re: Check Nut Size for Pulsar I (Sonja Englert)
2. 04:54 PM - Re: Check Nut Size for Pulsar I (mike mccann)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Check Nut Size for Pulsar I |
Typically jam nuts on rod ends are 1/4-28 threads (bolt diameter 1/4"). I
am sure there are no size AN6 rod ends on a Pulsar.
Sonja
On Fri, Aug 7, 2020 at 2:44 PM Yellowhammer <coyler@sthpk-12.net> wrote:
>
> Greetings,
>
> I was wondering if anyone had the proper size for the check nuts that go
> on the Rod End Bearings on the control linkages for the Pulsar I.
>
> Mine were missing when I acquired my kit.
>
> They seem to be the same size that would fit on an AN-6 bolt.
>
> I cannot figure out how to order the correct size. All I have seen on Air
> Craft Spruce is for An-3 size.
>
> If I am looking up the nuts incorrectly please point me in the right
> direction.
>
> I cannot close out my wings until I have the four that are required for
> each wing's control linkages.
>
> Thanks in advance for the information as it is greatly appreciated.
>
> Yellowhammer
>
> --------
> J.M. Oyler "Clyde"
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=497567#497567
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Check Nut Size for Pulsar I |
I can confirm when I get to the hanger as my Pulsar 1 manuals are there,
but I'm quite sure Sonja is correct.
Mike McCann
Pulsar 1-582
On Sat, Aug 8, 2020 at 7:06 AM Sonja Englert <paqs345@gmail.com> wrote:
> Typically jam nuts on rod ends are 1/4-28 threads (bolt diameter 1/4"). I
> am sure there are no size AN6 rod ends on a Pulsar.
>
> Sonja
>
> On Fri, Aug 7, 2020 at 2:44 PM Yellowhammer <coyler@sthpk-12.net> wrote:
>
>>
>> Greetings,
>>
>> I was wondering if anyone had the proper size for the check nuts that go
>> on the Rod End Bearings on the control linkages for the Pulsar I.
>>
>> Mine were missing when I acquired my kit.
>>
>> They seem to be the same size that would fit on an AN-6 bolt.
>>
>> I cannot figure out how to order the correct size. All I have seen on Air
>> Craft Spruce is for An-3 size.
>>
>> If I am looking up the nuts incorrectly please point me in the right
>> direction.
>>
>> I cannot close out my wings until I have the four that are required for
>> each wing's control linkages.
>>
>> Thanks in advance for the information as it is greatly appreciated.
>>
>> Yellowhammer
>>
>> --------
>> J.M. Oyler "Clyde"
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=497567#497567
>>
>>
>>
>>
>>
>>
>> ==========
>> ar-List" rel="noreferrer" target="_blank">
>> http://www.matronics.com/Navigator?Pulsar-List
>> ==========
>> FORUMS -
>> eferrer" target="_blank">http://forums.matronics.com
>> ==========
>> WIKI -
>> errer" target="_blank">http://wiki.matronics.com
>> ==========
>> b Site -
>> -Matt Dralle, List Admin.
>> rel="noreferrer" target="_blank">http://www.matronics.com/contribution
>> ==========
>>
>>
>>
>>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|