Today's Message Index:
----------------------
1. 08:03 AM - Injector Cleaning (Bill Judge)
2. 11:07 AM - Re: Injector Cleaning (John Morgensen)
3. 02:42 PM - Re: Injector Cleaning (vanremog@aol.com)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Injector Cleaning |
Lycoming instructions are here:
http://www.lycoming.com/Portals/0/techpublications/serviceinstructions/SI%201275C%20%2809-23-2008%29/Cleaning%20Fuel%20Injector%20Nozzles.pdf
I cleaned mine after 1000 hrs of operation and my fuel burn dropped by 0.5
gph when running lean of peak.
Gradually they got worse at atomizing the fuel and I wasn't able to run as
lean.
Its easy enough to do that I'll probably do it at each annual.
1 hr is a bit long for the hoppes, 20 minutes is recommended, at $30
ultrasonic cleaner might be worthwhile also:
http://www.amazon.com/Professional-Ultrasonic-Jewelry-Eyeglass-Cleaning/dp/B001DKDAVW
Bill
N84WJ, RV-8, 1097 hrs
RV-8.blogspot.com
>
> 1. 11:22 AM - Cleaning fuel injectors (Charles Brame)
> 2. 11:49 AM - Re: Cleaning fuel injectors (vanremog@aol.com)
> 3. 02:13 PM - Re: Cleaning fuel injectors ()
> 4. 03:46 PM - Re: Cleaning fuel injectors (Bill Gill)
> 5. 03:51 PM - Re: Cleaning fuel injectors (Lyle Peterson)
> 6. 04:59 PM - Re: Cleaning fuel injectors (Charles Kuss)
> 7. 04:59 PM - Re: Cleaning fuel injectors (Charles Kuss)
>
>
> ________________________________ Message 1
> _____________________________________
>
>
> Time: 11:22:20 AM PST US
> From: Charles Brame <ChasB@satx.rr.com>
> Subject: RV-List: Cleaning fuel injectors
>
>
> I have an Air Flow Performance fuel injection system on my Lycoming O-320.
> The
> AFP manual recommends cleaning the fuel injectors every 100 hours. Other
> than
> soaking in Hoppes #9, no detailed instructions are given for cleaning the
> injectors.
>
> What is the best, approved, method for cleaning fuel injectors?
>
> Charlie Brame
> RV-6A N11CB
> San Antonio
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Injector Cleaning |
Any idea on a recommended solution to use in an ultrasonic? I have seen
admonitions against using volatile solutions like Hoppe's #9 or MEK but
no information on what should be used. I use an ultrasonic for cleaning
rifle cartridges and the solution is intended for brass but I don't know
if it would be ok for injectors.
john
RV9A
On 1/5/2015 8:02 AM, Bill Judge wrote:
> Lycoming instructions are here:
> http://www.lycoming.com/Portals/0/techpublications/serviceinstructions/SI%201275C%20%2809-23-2008%29/Cleaning%20Fuel%20Injector%20Nozzles.pdf
>
> I cleaned mine after 1000 hrs of operation and my fuel burn dropped by
> 0.5 gph when running lean of peak.
>
> Gradually they got worse at atomizing the fuel and I wasn't able to
> run as lean.
>
> Its easy enough to do that I'll probably do it at each annual.
>
> 1 hr is a bit long for the hoppes, 20 minutes is recommended, at $30
> ultrasonic cleaner might be worthwhile also:
> http://www.amazon.com/Professional-Ultrasonic-Jewelry-Eyeglass-Cleaning/dp/B001DKDAVW
>
> Bill
> N84WJ, RV-8, 1097 hrs
> RV-8.blogspot.com <http://RV-8.blogspot.com>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Injector Cleaning |
=0AYou might want to give this juice a try.=0A =0Ahttp://www.u
ltrasonicsdirect.com/12decacl.html?productid=12decacl&channelid=FROOG=0A =0A
=0A =0A-----Original Message-----=0AFrom: John Morgensen <john@morg
ensen.com>=0ATo: rv-list <rv-list@matronics.com>=0ASent: Mon, Jan 5,
2015 11:07 am=0ASubject: Re: RV-List: Injector Cleaning=0A=0A=0A
=0A Any idea on a recommended solut
ion to use in an ultrasonic? I have seen admonitio
ns against using volatile solutions like Hoppe's #9 or
MEK but no information on what should be used. I use an
ultrasonic for cleaning rifle cartridges and the solut
ion is intended for brass but I don't know if it
would be ok for injectors.=0A =0A john=0A
RV9A=0A =0A =0AOn 1/5/2015 8:02 AM, Bill Judg
e wrote:=0A =0A =0A =0A
=0ALycoming instructions are here:=0A http://
www.lycoming.com/Portals/0/techpublications/serviceinstructions/SI%201275C%20%28
09-23-2008%29/Cleaning%20Fuel%20Injector%20Nozzles.pdf=0A
=0A=0A =0A =0AI cleaned mine
after 1000 hrs of operation and my fuel burn
dropped by 0.5 gph when running lean of peak.=0A
=0A=0A =0A =0AGradu
ally they got worse at atomizing the fuel and I wasn't
able to run as lean.=0A =0A
=0A =0A =0AIts easy enough t
o do that I'll probably do it at each
annual.=0A =0A=0A =0A
=0A1 hr is a bit long for the hoppes, 20 minutes
is recommended, at $30 ultrasonic cleane
r might be worthwhile also:=0A
=0Ahttp://www.amazon.com/Professional-Ultrasonic-Jewelry-Eyeglass-Clean
ing/dp/B001DKDAVW=0A =0A =0A=0A
=0A =0ABill=0A
=0AN84WJ, RV-8, 1097 hrs=0A =0ARV-8.blogspot.com=0A
=0A =0A =0A=0A
=0A =0A =0A =0A
===========================
===========================
===========================
===========================
====================0A=0A=0A=0A
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|