Today's Message Index:
----------------------
1. 10:37 AM - Re: Need Repair Advice... (rob ray)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need Repair Advice... |
--> RV4-List message posted by: rob ray <smokyray@yahoo.com>
Thanks Arvil, I will pass it on to John...
RR
arvil@bellsouth.net wrote:
Rob,
If the metal is not stretched to much he can take a leather
bag with shot in it and have someone hold it on the out side
over the dented area ,then from the inside he can use a
leather or rubber mallet to carefully smooth out the dent,
if this dosent work it might be best to make a dubber and
install a patch, It allso can be filled in with flexbond typ
filler but the paint will need to be removed, Last but not
least you could just leve it like it is as long as ther is
no cracks
Arvil
rob ray wrote:
>
> Note: forwarded message attached.
>
> ----------------------------------------------------------
> How low will we go? Check out Yahoo! Messengers low
> PC-to-Phone call rates.
>
> -----------------------------------------------------
>
> Subject: RV4-List Digest: 1 Msgs - 05/06/06
> Date: Sat, 6 May 2006 23:57:34 -0700
> From: RV4-List Digest Server
> To: RV4-List Digest List
>
> *
>
> ==================================================
> Online Versions of Today's List Digest Archive
> ==================================================
>
> Today's complete RV4-List Digest can also be found in either of the
> two Web Links listed below. The .html file includes the Digest formatted
> in HTML for viewing with a web browser and features Hyperlinked Indexes
> and Message Navigation. The .txt file includes the plain ASCII version
> of the RV4-List Digest and can be viewed with a generic text editor
> such as Notepad or with a web browser.
>
> HTML Version:
>
> http://www.matronics.com/digest/rv4-list/Digest.RV4-List.2006-05-06.html
>
> Text Version:
>
> http://www.matronics.com/digest/rv4-list/Digest.RV4-List.2006-05-06.txt
>
> ================================================
> EMail Version of Today's List Digest Archive
> ================================================
>
>
> ----------------------------------------------------------
> RV4-List Digest Archive
> ---
> Total Messages Posted Sat 05/06/06: 1
> ----------------------------------------------------------
>
>
> Today's Message Index:
> ----------------------
>
> 1. 10:27 AM - Need Repair Advice (John DeCuir)
>
>
>
> ________________________________ Message 1 _____________________________________
>
> Time: 10:27:07 AM PST US
> From: John DeCuir
> Subject: RV4-List: Need Repair Advice
>
> --> RV4-List message posted by: John DeCuir
>
> I had a minor accident recently, and would appreciate any advice on
> repair. After a pre-dawn run-up, I turned to go to the runway and ran
> over an unlit barricade ( the portable plastic type with two lamps,
> about 16 inches high at the lamps). The only damage is to the wheel
> pant fairing, which is a simple glass repair, and the aft fuselage,
> which is trickier. There is a gradually deepening dent, ending abruptly
> at a bulkhead that is not damaged. It's about 1/4" deep, and 1 1/2"
> wide, at the radius. The paint is intact, but slightly scuffed. It's
> accessible thru the baggage area , But what is the best way to push
> this out? I'm a non-builder owner, but do most of the maintenance
> myself, and would like to keep it that way, but I don't want to make
> this worse than it is now. It's barely noticeable now, and I'd like to
> push it out without blowing off the paint.
>
> John DeCuir
> N204CP, RV4
> SNS, CA
>
>
>
>
>
>
>
>
>
>
>
>
>
---------------------------------
How low will we go? Check out Yahoo! Messengers low PC-to-Phone call rates.
---------------------------------
How low will we go? Check out Yahoo! Messengers low PC-to-Phone call rates.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|