  | 
				Matronics Email Lists Web Forum Interface to the Matronics Email Lists   
				 | 
			 
		 
		 
	
		| View previous topic :: View next topic   | 
	 
	
	
		| Author | 
		Message | 
	 
	
		jjessen(at)rcn.com Guest
 
 
 
 
 
  | 
		
			
				 Posted: Fri Feb 03, 2006 10:09 am    Post subject: Trying to find a Robin | 
				     | 
			 
			
				
  | 
			 
			
				Robin  Wessel, if you're monitoring the list, can  you send me an email offline.  We're trying to get a dinner arranged of  Oregon RV-10 builders for next week, the opportunity based on Tim's visit for  transition training, and we cannot locate an email for you.   Thanks 
 John Jessen
    ~328 
 do not  archive
 
    From: owner-rv10-list-server(at)matronics.com  [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of  bob.kaufmann
 Sent: Friday, February 03, 2006 6:03 AM
 To:  rv10-list(at)matronics.com
 Subject: RE: 3 ring binder for  manual
  
   
 John 
   
 I laughed so hard, my sides hurt and now I  have to go to work and protect this country.  The pain in my side may be  the beginning of a national emergency because of the  laughter. 
   
 Bob K 
 Forward top  cowling    
  
 From:  owner-rv10-list-server(at)matronics.com  [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of John Jessen
 Sent: Thursday, February 02, 2006 9:12  AM
 To:  rv10-list(at)matronics.com
 Subject: RE: 3 ring binder for  manual
  
   
 I just rip each page  out (I've given up trying to keep the holes from ripping), immediately spill  some hot tea on it to give it its proper staining, fold it up and stuff it in my  briefcase so I can unfold it in the airport and look at it seriously hoping to  impress someone with my technical acumen.  Mainly I take the page out so I  can have that one page near, beside, on top of the work at hand.  Then,  once finished with it, I take it home with me so it's near the computer and I  can enter my notes and time, then finally onto a "completed" file of other,  heroically stained and mangled pages.  War is war.  I stand on the  front line between aluminum and civilization.  You need me on that line;  you want me on that line.  I don't have the time, nor the inclination to  pamper my pages.   
   
 Histrionically  yours, 
   
 John  Jessen 
   ~328 (skinning  the Tailcone) 
     
  
 From:  owner-rv10-list-server(at)matronics.com  [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Chuck Jensen
 Sent: Thursday, February 02, 2006 8:01  AM
 To:  rv10-list(at)matronics.com
 Subject: RE: 3 ring binder for  manual 
 To reinforce the pages  and prevent rip-out, run a strip of Scotch tape along the edge of the page,  covering the holes.  Punch the holes again and you have a super strong edge  with holes that won’t rip out.  Cost: 0.01 cents per  page. 
    
 Chuck  Jensen
  
    
 -----Original  Message-----
 From:  owner-rv10-list-server(at)matronics.com  [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Mike Lauritsen -  Work
 Sent: Thursday, February  02, 2006 10:41 AM
 To:  rv10-list(at)matronics.com
 Subject: RE: 3 ring binder for  manual 
   
 It’s a bit overkill,  but I took two strips of 1/8”x3/4” aluminum from the hardware store and drilled  them to correspond to the holes.  I countersunk and attached #8 nutplates  to one for the back and countersunk and inserted #8 screws through the front to  sandwich all of the pages together.  I went this route mainly because I had  so many ripped pages that I needed something to pinch and hold them  together. 
    
 Mike  
  
   
 -----Original  Message-----
 From:  owner-rv10-list-server(at)matronics.com  [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Chris Hukill
 Sent: Thursday, February 02, 2006 12:23  AM
 To:  rv10-list(at)matronics.com
 Subject: 3 ring binder for  manual 
    
 Has anyone found a mail order  source for a 3 ring binder for the manual? I keep tearing the holes on mine, and  would like to have a real binder for my manual, but I can't find any locally, or  on the internet. If anyone knows a source, please let me  know.
   
 Thanx
   
 Chris  Hukill
   
 Figuring out my aux fuel tank  system
 
  |  | - The Matronics RV10-List Email Forum - |  |   |  Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
 
  http://www.matronics.com/Navigator?RV10-List |  
  |  
 
 
 
 
  | 
			 
		  | 
	 
	
		| Back to top | 
		 | 
	 
	
		  | 
	 
	
		 | 
	 
 
  
	 
	    
	   | 
	
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
  | 
   
 
  
Powered by phpBB © 2001, 2005 phpBB Group
  
		 |