Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Oil Hose

Matronics Email Lists Forum Index -> Europa-List

View previous topic :: View next topic

Author Message

MJKTuck(at)cs.com
Guest

Posted: Mon Mar 02, 2015 9:00 pm Post subject: Oil Hose

Hi All,



I'm looking to replace my oil hoses. The one from the pump to the 

radiator has a 90 deg bend in it. I had noted that it was suggested I 

contact Lockwood as they have a metal 90 deg adapter to which regular 

hose could be fitted. I contacted them and they said just to use 'an AN 

fitting size -8'. Looking at the manual though the thread seems to be 

14.4mm so I'm not sure what they meant now. I wonder if they meant to 

make a 90 deg elbow using AN fittings. I couldn't figure the parts I 

would need though.



Any help as to what others have done would be appreciated.



Also, are there any US sources for the rubber engine mounts or are they 

uniquely Europa, in which case I would contact the factory in the UK.



Regards,

Martin Tuck

N152MT

Wichita, KS

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

alanb(at)dpy01.co.uk
Guest

Posted: Mon Mar 02, 2015 11:08 pm Post subject: Oil Hose

Replaced mine last year and used normal oil hose with no bends and no 90 deg bend on the pump.



route of hose work ok without any kinks or tight bends.



Alan

G-OBJT

 	  Quote: 	
		   On 3 Mar 2015, at 04:59, Martin Tuck <MJKTuck(at)cs.com> wrote:

 

 

 

 Hi All,

 

 I'm looking to replace my oil hoses. The one from the pump to the radiator has a 90 deg bend in it. I had noted that it was suggested I contact Lockwood as they have a metal 90 deg adapter to which regular hose could be fitted. I contacted them and they said just to use 'an AN fitting size -8'. Looking at the manual though the thread seems to be 14.4mm so I'm not sure what they meant now. I wonder if they meant to make a 90 deg elbow using AN fittings. I couldn't figure the parts I would need though.

 

 Any help as to what others have done would be appreciated.

 

 Also, are there any US sources for the rubber engine mounts or are they uniquely Europa, in which case I would contact the factory in the UK.

 

 Regards,

 Martin Tuck

 N152MT

 Wichita, KS

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

max8992

Joined: 28 Jul 2011
Posts: 142

Posted: Tue Mar 03, 2015 12:49 am Post subject: Oil Hose

So did I with normal (but adequate) oil hose. Just take of care of the route

you give to it and avoid short turns!



Max  Cointe

F-PMLH Europa XS_TriGear

Kit #560-2003 912ULS/AirmasterAP332 540 hours



F-PLDJ Dyn’Aéro MCR 4S 

Kit #27-2002 912ULSFR/MTProp MTV7A 1660 heures

-----Message d'origine-----

De : owner-europa-list-server(at)matronics.com

[mailto:owner-europa-list-server(at)matronics.com] De la part de Alan Burrill

Envoyé : mardi 3 mars 2015 08:08

À : Europa Forum Forum

Objet : Re: Oil Hose






Replaced mine last year and used normal oil hose with no bends and no 90 deg

bend on the pump.



route of hose work ok without any kinks or tight bends.



Alan

G-OBJT

 	  Quote: 	
		   On 3 Mar 2015, at 04:59, Martin Tuck <MJKTuck(at)cs.com> wrote:

 

 

 

 Hi All,

 

 I'm looking to replace my oil hoses. The one from the pump to the radiator

has a 90 deg bend in it. I had noted that it was suggested I contact
	


Lockwood as they have a metal 90 deg adapter to which regular hose could be

fitted. I contacted them and they said just to use 'an AN fitting size -8'.

Looking at the manual though the thread seems to be 14.4mm so I'm not sure

what they meant now. I wonder if they meant to make a 90 deg elbow using AN

fittings. I couldn't figure the parts I would need though.

 	  Quote: 	
		   

 Any help as to what others have done would be appreciated.

 

 Also, are there any US sources for the rubber engine mounts or are they

uniquely Europa, in which case I would contact the factory in the UK.
	


 	  Quote: 	
		   

 Regards,

 Martin Tuck

 N152MT

 Wichita, KS

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

_________________
Max8992
Europa XS #560 F-PMLH

h&jeuropa

Joined: 07 Nov 2006
Posts: 649

Posted: Tue Mar 03, 2015 5:08 am Post subject: Re: Oil Hose

Martin,



You need a AN8-M14.5 adaptor.  The old Rotax PN was 956641 but it doesnt appear in the parts list any longer.  



You can buy them at lots of places.  I often use Summit Racing for AN fittings.  The page with the adaptor is 



http://www.summitracing.com/search/part-type/an-to-metric-adapter-fittings/fitting-size-2/14mm-x-1-5/fitting-size-1/minus-8-an?N=4294920733%2B4294920642%2B4294947250&SortBy=Default&SortOrder=Default



You will also need a 90 deg hose end and I purchased Aeroquip FNC0820 hose for this.  Works fine.



Jim

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

mau11(at)orange.fr
Guest

Posted: Tue Mar 03, 2015 12:21 pm Post subject: Oil Hose

One very good solution for the oil hose is  "Parker Push-lok 836" 1/2 " 

colour blue 150Â°C max



Michel AUVRAY



Le 03/03/2015 05:59, Martin Tuck a Ã©crit :

 	  Quote: 	
		   



 Hi All,



 I'm looking to replace my oil hoses. The one from the pump to the 

 radiator has a 90 deg bend in it. I had noted that it was suggested I 

 contact Lockwood as they have a metal 90 deg adapter to which regular 

 hose could be fitted. I contacted them and they said just to use 'an 

 AN fitting size -8'. Looking at the manual though the thread seems to 

 be 14.4mm so I'm not sure what they meant now. I wonder if they meant 

 to make a 90 deg elbow using AN fittings. I couldn't figure the parts 

 I would need though.



 Any help as to what others have done would be appreciated.



 Also, are there any US sources for the rubber engine mounts or are 

 they uniquely Europa, in which case I would contact the factory in the 

 UK.



 Regards,

 Martin Tuck

 N152MT

 Wichita, KS

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

paul.the.aviator(at)gmail
Guest

Posted: Tue Mar 03, 2015 2:08 pm Post subject: Oil Hose

Hello Everyone,



Although slightly off topic, I did go down the route of replacing all of my hoses with AN fittings and very flexible steel braided hose from Pegasus Racing.  Frans did the same but he used the Kevlar version of the hose which is even more flexible.



I had to TIG  weld on some fittings onto my oil tank and make a banjo for the sump, although I believe there is a Rotax part for this.



It's an expensive exercise, it cost me about $500 at the time, but I no longer have to be concerned about hoses chaffing or getting too hot.  



I have attached the bill of materials and the part numbers are from the Pegasus catalogue

Paul

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

Europa_AN_Fitting_BOM.XLSX

Description:

Download

Filename:

Europa_AN_Fitting_BOM.XLSX

Filesize:

11.58 KB

Downloaded:

382 Time(s)

MJKTuck(at)cs.com
Guest

Posted: Tue Mar 03, 2015 6:35 pm Post subject: Oil Hose

Thank you all who responded for taking the time to provide some very 

helpful information.



Martin Tuck



On 3/3/2015 4:06 PM, Paul McAllister wrote:

 	  Quote: 	
		   Hello Everyone,



 Although slightly off topic, I did go down the route of replacing all of my hoses with AN fittings and very flexible steel braided hose from Pegasus Racing.  Frans did the same but he used the Kevlar version of the hose which is even more flexible.



 I had to TIG  weld on some fittings onto my oil tank and make a banjo for the sump, although I believe there is a Rotax part for this.



 It's an expensive exercise, it cost me about $500 at the time, but I no longer have to be concerned about hoses chaffing or getting too hot.



 I have attached the bill of materials and the part numbers are from the Pegasus catalogue

 Paul

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Europa-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum